Building GluonCS on C#

All questions related to the configuration tool and groundstation

Moderator: lukasz

Building GluonCS on C#

Postby Rico21 » Thu Oct 18, 2012 7:35 am

Hi Tom,

When I try to use the write command to setup the config, I get this error message:


[09:12:22.41] Error checksum
[09:12:22.42] ERROR received data: $SI;0;c;f;b;e;?*49a

To study this error I want to have a look in the software of the GluonCS but I can't build it. One file is perhaps missing:
C:\Users\Eric\Mes Projets\Gluonpilot\trunk\Software\Gluonconfig\GluonCS\GluonCS.csproj : error : Impossible de lire le fichier projet 'GluonCS.csproj'.

I'm using FTDI cable and my hardware is V0.1 #6

Thanks for your help
Regards
Eric
Rico21
 
Posts: 30
Joined: Fri Nov 27, 2009 5:06 pm
Location: France

Re: Building GluonCS on C#

Postby Tom » Fri Oct 26, 2012 8:20 pm

Sorry, still in progress. I've got so much work to do with GP2 that I don't know what to do first :-)
No worries, I'll get there :-)
User avatar
Tom
Site Admin
 
Posts: 1016
Joined: Fri Nov 13, 2009 6:27 pm
Location: Belgium

Re: Building GluonCS on C#

Postby Rico21 » Sat Oct 27, 2012 4:01 pm

Hi Tom,

In addition to my post above, I would like to bring the following points to you:
When I call the "basic configuration" screen I get an error message which I have attached the screen snapshoot below. If I press "continue" then I can set all the parameters correctly on this "easyconfig". When I press "burn and close" the transaction seems to be ok. The Gluonpilot module uses well this setting. But, if I power off the module and I power on again, I lost this configuration even the flightplan.
It seems there is a "write" but not a "burn" into the flash memory.

I don't know if it is a firmware or software problem.

For the parameters which are under the "full configuration" screen: telemetry, servo, pid etc... each time I try to write them I get an error of the type :
[09:12:22.41] Error checksum
[09:12:22.42] ERROR received data: $SI;0;c;f;b;e;?*49a

I'm using the v0.8 version with a hardware v0.1i
Thank you for your help

regards

Eric
Attachments
message.doc
(120 KiB) Downloaded 1485 times
Rico21
 
Posts: 30
Joined: Fri Nov 27, 2009 5:06 pm
Location: France

Re: Building GluonCS on C#

Postby Tom » Sat Oct 27, 2012 4:46 pm

Hi Eric,

The $SI command is the burn a navigation line.
Do you have a gluonpilot with 1MB or 2MB memory?
User avatar
Tom
Site Admin
 
Posts: 1016
Joined: Fri Nov 13, 2009 6:27 pm
Location: Belgium

Re: Building GluonCS on C#

Postby Rico21 » Sat Oct 27, 2012 5:11 pm

Hi Tom,

The flash memory chip is ATMEL 45DB161D-SU, that is 16 MBits.

Regards

Eric
Rico21
 
Posts: 30
Joined: Fri Nov 27, 2009 5:06 pm
Location: France

Re: Building GluonCS on C#

Postby Tom » Sun Oct 28, 2012 7:09 pm

Hi Eric,

This error probably occurred because you don't have a valid configuration. Please load the factory settings and do you configuration.
User avatar
Tom
Site Admin
 
Posts: 1016
Joined: Fri Nov 13, 2009 6:27 pm
Location: Belgium

Re: Building GluonCS on C#

Postby Rico21 » Mon Oct 29, 2012 1:05 pm

Hi Tom

After many trials I finally solved the problems I encountered. I usually start with programs "source" and compile them for either the software or firmware. Today I tried from executables (using the bootloader) which are available for download and it works! :lol:
Regarding the firmware it seems, there is something different between sources "SVN" compiled by myself and the executable available for download. Which difference? I don't know. :?:
Regarding software GCS the file "GluonCS.csproj " is to be included.

I have a request to solve a display problem: is it possible to change the settings of the window "EasyConfig"? My "little field" laptop which has a resolution of 1024x600 does't give me access to control buttons at the bottom of this window. I can't change this.

Thank you, Tom

Best regards

Eric
Rico21
 
Posts: 30
Joined: Fri Nov 27, 2009 5:06 pm
Location: France

Re: Building GluonCS on C#

Postby Tom » Mon Oct 29, 2012 5:25 pm

Hello Eric,

In the next version this will be solved. Gluonconfig will have 4 tabs:
- Tab 1: Something similar to easyconfig
- Tab 2: OSD configuration
- Tab 3: Advanced config (current gluonconfig)
- Tab 4: Datalogging

So the smaller gluonconfig screen will be a good match for your laptop :-)
User avatar
Tom
Site Admin
 
Posts: 1016
Joined: Fri Nov 13, 2009 6:27 pm
Location: Belgium

Re: Building GluonCS on C#

Postby Rico21 » Tue Oct 30, 2012 10:19 pm

Thank you, Tom for this good news, always one step ahead!
thank you
greetings
Rico21
 
Posts: 30
Joined: Fri Nov 27, 2009 5:06 pm
Location: France

Re: Building GluonCS on C#

Postby sochnedo » Wed Mar 11, 2015 1:31 pm

If I press "continue" then I can set all the parameters correctly on this "easyconfig". When I press "burn and close" the transaction seems to be ok. The Gluonpilot module uses well this setting. But, if I power off the module and I power on again, I lost this configuration even the flightplan. It seems there is a "write" but not a "burn" into the flash memory.>???
Get Braindumps demos for spanish programs Our high quality itil prepares you well before appearing in the final spanishprograms - what is the spanish word for language and livemocha exams
sochnedo
 
Posts: 2
Joined: Wed Mar 11, 2015 1:29 pm

Next

Return to Software

Who is online

Users browsing this forum: No registered users and 3 guests

cron